Share It!!!



Command Sequence Configurations


Herewith the example of command sequence in TEMS 6.1.4

Voice Call CS

i.e “120/15” means 120 second on call then call end, 15 second wait and then call again.

1. Loop Start give the number of repetition for command below the loop start (General -> Loop Start)

2. Dial select the MS and give the destination number (Voice -> Dial)

cs-ms1











3. Synchronize to synchcronize MS before go to the next command (General -> Synchronize)
cs-sync
















4. Wait 120 wait 120s on call (General -> Wait)

5. End Call (Voice -> End Call)

6. Wait 15 wait 15 before call again (General -> Wait)

7. Loop End (General -> Loop End)

Video Call CS

In general cs for video call is same as voice call, but in video call in dial command we must add “v”.

i.e

Loop Start

Dial v081384760975

Wait 120

End Call

Wait 15

Loop End

Packet Service (PS) Test

This is the example cs for PS test

cs-ps








All equipment that we use in PS Test is DC (Data Cable).

In command dial up :

DT *99***1# orinaica ************

means DT is dial up connection that we should made first in network connection
cs-pspre01



















setup account for this connection (fill username and password : orinaica and ***********)

cs-pspre02




















select modem that we want to use in PS Testcs-pspre03























give additional command (at command, “orinaica.wordpress.com” is the apn name that will use in connection)
cs-pspre04





















*99***1# is the dial number for dial up connection
cs-pspre05




















this is details to make cs in PS Test

Data Services

Dial Up (Connect -> Dial Up)

Phonebook Entry use DT (dial up connection that we’ve made before)

Phone Number : Dial Up number for dial up connection

Username : username of account network connection

Password : password of account network connection
cs-psdialup



















FTP Get (Session -> FTP -> Get)

Equipment Name : Select equipment name

Source File : Select file that will “get” from ftp server

Target File : Destination folder where file will be place

PASV : Disable

Remote Address : IP Address of the FTP Server

Username : Username for log in to FTP Server

Password : Password for log in to FTP Server
cs-psget




















Trackbacks & Pingbacks

Comments

  1. kalau IP assigned dari provider bukan IP publik, PASV pada FTP set pada ENABLE.

    | Reply Posted 6 years, 12 months ago
    • * orinaica says:

      Thanks dham…
      Share more ur experience in my blog ya…

      | Reply Posted 6 years, 12 months ago
  2. * raka says:

    thanx for share…

    oia,,
    bedanya short call sama long call apaan yah??
    klo bisa dijelasin yg jelas, maklum newbie, hehe

    | Reply Posted 6 years, 10 months ago
    • * orinaica says:

      Short call atau sequence dalam command sequence biasanya digunakan untuk mengecek accessibility (Call Settup Success Rate).
      Contoh :
      Short Call 60/10 artinya 60 second dedicated mode, dan 10 second idle mode.
      Short Call 120/10 artinya 120 second dedicated mode, dan 10 second idle mode.

      Long call biasanya digunakan untuk mengecek Integrity dan Retainability (Handover Success Rate, Dropped Call Rate).
      CMIIW😉

      | Reply Posted 6 years, 9 months ago
  3. * SAGSIVA says:

    wow keren postingnya,,,
    mw tanya nie mbk, bs ngasih contoh command sequence untuk modus short call & long call g???skalian maksudnya klo bs??? & klo bs yg tems 8

    | Reply Posted 6 years, 9 months ago
  4. * dinzo says:

    bro minta tolong buat bikin comand sequence buat XL untuk download data di server publik….terimakasih….

    | Reply Posted 6 years, 9 months ago
  5. * hermianto says:

    tanya donk!!

    itu setup new connection wizard nya utk operator apa?
    apa bisa utk semua operator?

    thanks b4

    | Reply Posted 6 years, 8 months ago
    • * orinaica says:

      untuk dial up connetion.
      bisa untuk semua operator boss…

      Regards,
      orinaica

      | Reply Posted 6 years, 8 months ago
  6. * Noberic says:

    Kalau Test *123# atau *888# bisa tidak di command sequence, kok saya coba tidak bisa yach, jatuhnya malah nelpon. mohon pencerahannya.

    trims

    | Reply Posted 6 years ago
    • * orinaica says:

      Halo mas,… udah coba pakai at command?
      AT+CKPD=”:R:R:R:R:R:R*123#:j”

      goodluck
      -orinaica-

      | Reply Posted 6 years ago
      • * Noberic says:

        Matur nuwun, Mas bisa digunakan.

        Posted 6 years ago


Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: