Drive Test using TEMS
In general, Drive Test can be define as a methode that used to verify the actual condition of RF signal certain operator (excelcomindo, telkomsel, indosat, mobile8) at certain place.
Several functions of drive test :
– Analyzing customer complaint of certain operator in their home or office area
– Finding problem in BTS ( Timeslot Check, TRX Check, Swap Feeder)
– Analyzing the result of optimization process (continuity and all of area)
There are softwares can be used for drivetest that installed on laptop. TEMS Investigation (Ericsson), NEMO (Nokia).
Here the steps to start learning drivetest with TEMS Investigation :
3. TEMS Investigation :
– Port Equipment Configurations
– Command Sequence Configurations
6. Post Processing :
7. Trouble Shooting :
– Antenna Tilt
Tolong kritik dan tambahan atas kekurangan artikel diatas ya!!!
| Posted 15 years, 1 month agoThx
First of all, English please ..
I would like to say, that was a nice introduction. There should be a lot objectives on drive test, and would recommend to move on further short description on technical how-to, e.g. refer to TEMS menus or features. Though that previous posts on other blog you’ve written is good, why don’t you import them into this blog?
Higher level on using of such field test tool surely will make this blog very interesting, such as tips, drive test KPI and post processing.
The following terminologies and functionality shall be considered for that:
– information element description on GSM/GPRS/EDGE/WCDMA/HSPA on TEMS;
– how to prepare cell file;
– how to create theme of radio parameters;
– exporting TEMS log into other format;
– generating drive test report using TEMS wizard;
– Route Analysis how-to
– frequency plan and tuning using TEMS map;
– use case of frequency scanning and interference investigation;
– use case of swapped antenna/feeder;
– use case of missing neighbors;
– use case of overshoot or island coverage;
– use case of pilot pollution identification;
– use case of model tuning
– use case of hardware defective identification;
– use case of signal propagation characteristic on particular clutter type;
Hope it will not confuse you, as you have requested for some feedback π
Cheers.
| Posted 15 years, 1 month agowaw, thanks a lot for your feedback mr.gigih.
yes, i’ll try to make more details “how to” in the other page of my blog.
from terminology that u’ve said,
that was made me have more knowledge about the function of drivetest.
thank you.
and i hope u’ll never tired to give advice.
*sorry if my english too bad π
| Posted 15 years, 1 month agohow to create a log file and upload after DT?
Posted 10 years, 8 months agogood job mr isa, keep writing, learning, and sharing… try to learn DT pre analysis
| Posted 15 years, 1 month agothanks mr.pram for ur support.
| Posted 15 years, 1 month agoπ
mantaff gan..
keep going..
tak tunggu implementasi lanjut dr saran mas gigih..
| Posted 15 years, 1 month agook, thx mr.dedy.
| Posted 15 years, 1 month agonice to know u.
if u have any suggestion just share it,…
Waw..nice info mr. isa, it’s really useful. after i read your articles i got bookmark your blog soon on my browser :D. you are such of kind guy, many people aren’t as fair as you did for knowledge sharing. keep writing, sharing, and posting…
Bravo
| Posted 15 years, 1 month agothanks a lot mr.wea for ur comment, hopefully this article will be usefull for each other.
| Posted 15 years, 1 month agogood job guys…..let’s go to learn and learn….
| Posted 14 years, 10 months agothanks man,…
| Posted 14 years, 10 months agoπ
mr.isa, when I learn about drive test.. I hope coming soon when you back from Bandung…. Thanks…
| Posted 14 years, 9 months agoπ ok, i’ll tell u if i come back,…
| Posted 14 years, 9 months agothanks
ajib…mau mau mau lagi lagi lagi..!!
| Posted 14 years, 9 months agoThis is very good to beginners and i like to see the sample DT report, so it will be more help full to prepare our report. However this very good keep on adding and updating the things
| Posted 14 years, 6 months agoThank You Athula…
| Posted 14 years, 6 months agoNice Article,,this will increase my knowledge bout Drive test, thanks 4 share
| Posted 14 years, 2 months agoThanks…
| Posted 14 years, 2 months agour welcome π
Wow…
Nice blog, maN!!
keep going! i hope this blog is just a start, please share your experience, write more articles (and detailed).
As a newbie in DT, two thumbs up for you man!
i’ll bookmark your blog…
many thx man!
| Posted 13 years, 10 months agosorry man, my english so bad…i mean me as a newbie (not you)…raise my two thumbs up for you man! i hope you don’t mind with this. thx
| Posted 13 years, 10 months agoπ
same as you, i’m still learn how to explore my english in this blog.
thank you for your kind.
Sincerely Yours,
Posted 13 years, 10 months agoorinaica
Hi Irkfun,
Thanks for your advice,….
I hope, we can share our experience here,…
Sincerely Yours,
| Posted 13 years, 10 months agoorinaica
thks for u’r nice share…
| Posted 13 years, 8 months agour welcome…
| Posted 13 years, 8 months agoisa my men ..
u just unbelieveble bro, u r my idol seriously
nice share n keep writing,
i just want to ask u something
can u tell us about GSM and or WCDMA parameters please
so we can go drivetest not only just collecting data, but also analyze and realy know what are we doing for
so there is value added in our job, right ?
sukur mengarah ke optim bro, that will be so much noise .. hehe .. so nice kali ye
salam
| Posted 13 years, 6 months agoHi Gesang Thanks for your coming in my blog, π
Do you mean parameter in RBS/Node B?
That was a lot of parameters gesang, for ERICSSON you can read on ALEX and for SIEMENS open the E-DOC.
For drive test troubleshooting, u can see the behave on the RF condition.
For Example in GSM, take a look at several info elements such as :
– RxLevIdle (for coverage analysis)
– RxQual (Quality of RF based on BER)
– SQI (Quality of Voice based on BER & FER [Ericssonβ’])
– C/I (Co Channel Interference Indication, for No Hopping can tolerate > 12dB, Hopping can tolerate > 9dB)
– C/A (Adjecent Channel Interference Indication, for No Hopping can tolerate > -9dBm, Hopping can tolerate > -6 dBm)
In WCDMA, take a look at several info elements such as :
– CPICH RSCP (Receive Signal Code Power, Indication of Signal Strength)
– CPICH Ec/No (Ec/No is Energy of the Chip / Noise. This noise can be noise created by the 3G cell itself as the traffic increases, external noise source, other 3G cells causing a noise increase (pilot pollution))
– CPICH Ec/Io (Ec/Io is the Energy of the Chip / the noise made by this cell only)
For Packet Service (PS) test, see the Coding Scheme/Modulation Coding Scame (GPRS/EDGE) and Spreading Factor “SF” (WCDMA) for the level speed of downlink throughput. For investigate throughput caused of RF condition, we can see on lower layer (RLC Throughput). For user perception, see on Application Throughput and Session Application Throughput.
CMIIW
| Posted 13 years, 6 months agoThnK’s GOOD share !!!
LIke This
π
| Posted 13 years, 6 months agothank you π
| Posted 13 years, 5 months agomantap gan!!!
| Posted 13 years, 5 months agokapan nongkrong di mekdi? hehe
halo ndi,
| Posted 13 years, 5 months agokpn bos andi bisa aja…
I don’t know how use “report generator KPI”. Would you tell me about it?
| Posted 13 years, 4 months agoBr!
Mantep gan….
| Posted 13 years, 4 months agoseru nigh infonya, nambah experience
kapan bisa ngoprek bareng gan…
hehehehehe
halo pak yusman,…
thanks kunjungannya dan maaf kl isi blognya hanya basic2 saja.
gimana kabar pak?
ada project yg bisa kita garap?
π
meet @ chat ya gan,…
| Posted 13 years, 4 months agoNice post for the telecom newbie engineer…
| Posted 12 years, 11 months agoThanks Toto…
| Posted 12 years, 11 months agothis is really good especially for beginners but my problem is that we are using GENEX Probe V 2.3, can some one help me out? or if you know where can i get a page like this , where every thing is in detail, please tell me.
| Posted 12 years, 11 months agothanks a lot.
Thanks Ali, i havent use GENEX tool. Maybe if someone read your comment and know the answer, they’ll help you…
| Posted 12 years, 11 months agothnx to u dear. can u explain up link and down link interference in WCDMA, i haven’t found any satisfactory definition.
Posted 12 years, 11 months agohhhmmmmm its a good blog. thx yo
| Posted 12 years, 11 months agothanks pak Jainal,…
| Posted 12 years, 11 months agoThanks a lot Pak, these useful for newbie like me.
waiting for next tutorial, Drive Test with NEMO, Probe.
| Posted 12 years, 10 months agowaiting for free time brofahroe… π
Thanks for visiting this blog,
if you want to sharing something you can directly write here…
BR,
Isa
| Posted 12 years, 10 months agoplz tell my more detail about maio i understand some basic concept but i want compelete information about this
| Posted 12 years, 8 months agoHI Ahsan,
please check comment on https://orinaica.wordpress.com/2009/05/23/trx-check/.
BR,
| Posted 12 years, 8 months agoisa
Hello.
I have some problems with tuning Macro Model for UMTS in Asset 7.0
I made log files with extension .log using Tems Investigation 8.2.3. To calibrate my propagation model I need to download my log files and using Measurements botton in Tools I am able to do it.
But some problems appeared when I started downloading log files, namely :
1.When I make drive tests do I need to get attached to one particular cell and keep on getting attached to that cell while Tems loses signal strength (CPICH RSCP) from that cell or I can make drive tests in a scanner mode when I donβt attach to a particular cell and receive CPICH RSCP from all available Nodes B which there are in that place.
2.Asset 7.0 doesnβt understand log files with extension .log and I need to transform log files with extension .log into log files with extension .fmt using Tems Investigatin.
But the questiΠΎn is what parameters of UMTS I need to extract from log files with extension .log in order to generate log files with extension .fmt. ?????
I think that I need the folloving :
-active set scrambling code
-active set cell name
-active set CPICH RSCP
-latitude and longitude
In manual βAsset 7.0 User reference Guideβ on the page of 81 there is nothing about it!!!!!
On the page 89 something is mentioned about Cell ID and SC and that is all.
I am looking forward to receive a message from you
| Posted 12 years, 8 months agoBest wishes Sergei
Hi Sergei, thank you for coming and sorry for late response.
1. I haven’t do the propagation model before, but i think for propagation model, no need to lock only for SC for each Cell/Site. Its different thing if you want to make a Single Site Verification (SSV), you have to lock SC for each Cell/Site.
2. Select Export Logfile (*.log) into *.txt, when change the file type into *.fmt. I dont have any template for Asset.
BR,
| Posted 12 years, 7 months agoIsa
Nice sharing bro…its complete explanation step by step instruction.
| Posted 12 years, 4 months agothanks π
| Posted 12 years, 4 months agoDear All
presently i making Tems Drive Test Tutorials if you are interested please find the link
| Posted 12 years, 2 months ago
Thanks Nifrash, It’s really useful.
Keep update your shareable topics.
Rgrds,
| Posted 12 years, 2 months agoIsa
Hi All
| Posted 12 years, 2 months agoIts really a very nice informative site. thank you all
If some one needs to exchange information about drive testing using Genex Probe 2.3, for 3G lease share with me. tnx. again again again
Dear All
presently i making Tems Drive Test Tutorials if you are interested please find the link
| Posted 12 years, 1 month agoAnother Updates
Dear Nifrash
thank u for the vedios.
but I’m new with 3g can u help me about this?
-TEMS workspace for voice and vedio
-TEMS workspace for Data.
-post proccessing
-troubleshooting.
-layer 3
If u have reports can u share it plz.
my mail
spindary@gmail.com
BR,
Posted 11 years, 10 months agoDiyari
Nice share, i will learn from this. keep sharing.
| Posted 12 years, 1 month agohi,i am isaac,i wanna know how i can create routes and put them on tems,maybe lets say they are in google earth,please……….
| Posted 11 years, 11 months agoyou can use mapinfo2googlearth.mbx if you want to convert route that you made on mapinfo
| Posted 11 years, 11 months agowhy I cannot load cell files to Tems 9.1.4, while my friends can load the same cell files, I can load cell files i received in April but I have received cell files in May and I cannot load them, any help?
| Posted 11 years, 10 months agoHi Nasir, thanks for visiting my blog.
think you have to check the header of your cell file.
-isa-
| Posted 11 years, 10 months agoIβm sorry but would you please explain a little? what do you mean by checking header of cell file?
Posted 11 years, 10 months agoI’m sorry but would you please explain a little? what do you mean by checking header of cell file?
| Posted 11 years, 10 months agoPlease send me rf related knowledge
| Posted 10 years ago